Deliverability7 min read
What is a good email bounce rate? Benchmarks and fixes
Short answer
Sender guides call a bounce rate under 2% good, and some aim for under 0.5%. Amazon SES puts an account under review at 5% hard bounces and might pause sending at 10%. If your rate is higher, stop sending to the bounced addresses, find where they came from, and verify the list before your next send.
Key takeaways
- Bounce rate is bounced emails divided by emails sent, times 100. Check how your tool counts blocked messages.
- Guides call under 2% good. Amazon SES reviews an account at 5% hard bounces and might pause sending at 10%.
- Mailchimp and Brevo remove hard-bounced addresses for you. Your job is to find where those addresses came from.
- Verify the list, send a small batch, and read the next report before the full send.
What is an email bounce rate and how do you calculate it?
Your bounce rate is the share of sent emails that came back undelivered. Divide the bounced emails by the emails sent, then multiply by 100. If you send 10,000 emails and 150 bounce, your rate is 1.5%.
Tools count differently. Amazon SES's documentation says SES counts hard bounces only and leaves soft bounces out. Some providers also count blocked messages as hard bounces. Compare your number with a benchmark that uses the same definition, or you will chase a gap that does not exist.
What is the difference between a hard and a soft bounce?
A hard bounce has a permanent cause. Amazon SES's documentation gives the typical case: the email went to an address that does not exist. Mailchimp's help center describes a hard bounce as a permanent reason an email cannot be delivered and a soft bounce as typically a temporary issue. A full mailbox or a server that is down for a few hours are common soft bounces.
- Hard bounce: the address does not exist or will never accept mail. Remove it right away.
- Soft bounce: the email failed this time. Mailchimp keeps an address through several soft bounces before it treats the address as a hard bounce (details below).
What is a good email bounce rate?
Two sender guides give numbers you can aim for. HubSpot's German guide advises keeping your bounce rate under 2%, because many mail servers use the rate to classify spam. Brevo's German guide gives under 0.5% as a rule of thumb, with a delivery rate above 95%. Read both as guidance from email vendors.
Sending services publish limits that trigger action. The table shows what each source measures and what happens when you cross its line.
| Source | What it measures | Threshold | What happens |
|---|---|---|---|
| Amazon SES documentation | Hard bounces only | Below 5% for best results | At 5% or more the account goes under review |
| Amazon SES documentation | Hard bounces only | 10% or more | SES might pause sending |
| Brevo help center | Hard bounce rate | Above 2% | Listed among the triggers that can suspend a campaign or account |
| HubSpot guide (German) | Bounce rate | Under 2% | Guidance. Many servers use the rate to classify spam |
| Brevo guide (German) | Bounce rate | Under 0.5% | Guidance. Rule of thumb, with a delivery rate above 95% |
Guides ask for 2%, while SES opens its review at 5%. Staying just under an enforcement line leaves you no margin. In a list of 1,000 addresses, 50 hard bounces already make 5%. Read the rate per import and per sign-up source, because the overall average can hide one bad segment.
Why does a high bounce rate hurt your sending?
Mailbox providers read a high rate as a sign that you do not manage your list. Amazon SES's documentation says email providers interpret a high bounce rate as a sign that a sender is not properly managing their recipient list. The judgment has consequences: a sending service can review or pause your account, and HubSpot's guide notes that many servers use the rate to classify spam.
Yahoo's sender best practices point the same way. They ask senders to track hard bounces, soft bounces and inactive recipients, and to remove invalid recipients promptly. For how bounces fit into inbox placement, read why emails go to spam.
What do you do after a hard bounce in Mailchimp or Brevo?
Check why the address bounced, then fix it or drop it. Both tools have already taken it out of your sending flow. In most cases Mailchimp cleans a hard-bounced address from your audience automatically and immediately. Brevo's help center says hard-bounced addresses are blocklisted automatically.
- Mailchimp notes that valid addresses occasionally hard bounce. Look for a typo before you give up on a contact.
- Mailchimp's help center says cleaned contacts cannot be edited. Add the corrected address as a new contact.
- Do not re-import the old file. It still holds the addresses that bounced, and your next send repeats the damage.
- Soft bounces take longer. Mailchimp allows 7 soft bounces for an address with no subscriber activity and up to 15 for contacts with earlier activity, then treats the address as a hard bounce and cleans it.
How do you bring a high bounce rate down?
Stop the damage first, then fix the source. A high rate usually points at the list itself: addresses go stale, sign-up forms collect typos, and bought files bring in strangers. You can work through the steps below within one campaign cycle. Use the table to match the pattern you see to its likely cause.
| Pattern | Likely cause | First fix |
|---|---|---|
| A jump right after an import | Typos or outdated addresses in the imported file | Pause the send, verify the file, then retry with a small batch |
| A slow climb over months | List decay: people change jobs and addresses | Re-verify old segments before big sends |
| A high rate from one sign-up form | No confirmation step, so typos get in | Add confirmed (double) opt-in |
| Many bounces after adding a bought file | Addresses you never collected yourself | Stop using the file. Verification cannot make a bought list acceptable |
- Stop sending to the bounced addresses. Confirm your tool removed every hard bounce, and remove them yourself if it did not.
- Find where the bad addresses came from. Check the import, the sign-up form and the age of the file. Lists age too: estimates of yearly decay run from about 15% to 30% (see how fast email lists decay).
- Verify the list. An email verifier checks each address without sending mail and shows which ones cannot receive it. The email list cleaning checklist walks you through it, and how email verification works explains the checks.
- Send a small batch first. Pick a few hundred cleaned addresses and read the bounce rate before the full send.
- Read the next report. Compare it using the same definition as before. If the rate stays above your target, repeat step 2 for the segment that still bounces.
- Keep new addresses clean. Confirmed (double) opt-in, which Yahoo's best practices recommend, catches typos at sign-up.
Frequently asked questions
Is a 5% bounce rate bad?
It is high. HubSpot's guide advises under 2%, and Amazon SES puts an account under review at 5% hard bounces. Stop sending to the bounced addresses and verify the list before your next campaign.
How do I calculate my email bounce rate?
Divide the number of bounced emails by the number of emails sent, then multiply by 100. 150 bounces from 10,000 sends is 1.5%. Check whether your tool counts soft bounces or blocked messages, since definitions differ.
Do soft bounces count toward the bounce rate?
It depends on the tool. Amazon SES counts hard bounces only. Other providers count differently, and some treat blocked messages as hard bounces. Mailchimp turns an address with repeated soft bounces into a hard bounce after 7 or up to 15 attempts.
Can I re-add an address that Mailchimp cleaned?
Not by editing it. Mailchimp's help center says cleaned contacts cannot be edited, so add the corrected address as a new contact. Check the address first, because valid addresses occasionally hard bounce too.
Does a clean list mean a zero bounce rate?
No. Verification shows which addresses can receive mail today. Addresses also go bad later, and valid ones occasionally hard bounce. A rate near zero is a goal, and you keep it by rechecking old segments before big sends.